|
|
roof
curbs & vibration isolation (link to this
section of the catalog)
pate® curbs for
conventional buildings seal roof openings against leaks. Canted, no cant or raised
cant styles for a water-tight transition between roof and skylights, fans and other
equipment. Height: 8" or more above roof line. Heavy-gauge galvanized
steel or aluminum construction, with integral base plate, continuous welded and mitered
corners. Larger sizes internally reinforced. Pressure treated wood nailer, 1
½" thick fiberglass insulation, simple flashing detail. Sound attenuating
galvanized steel panels with fiberglass insulation absorb up to 40% of ventilator noise
with air flow interference of only 4%. Removable for maintenance.
how to curb vibration
To absorb excess vibration of rooftop hvac equipment, pate®
introduces isolation bases on its own roof curbs.
iso-bases on pate® curbs control
the vibration of rooftop air handling units by isolating them from building and roof
structure. Excess vibration of air conditioners, blowers, and exhausters is absorbed
by the highly efficient isolation base assembly. Upper and lower members of extruded
aluminum incorporate cadmium-plated steel springs selected for 1" static deflection
and sized and positioned to insure uniform deflection for the entire system. Frame
is sealed against water and weather. A continuous neoprene gasket is bonded to upper
and lower surfaces. pates's isolation base is a fully assembled
one-piece unit, easy to install, and available in sizes and capacities to meet exact
requirements. Available on pate curbs mated to AC equipment.
BACK TO TOP OF PAGE
|
|
 |
|
 |
|
|
|
|
|
|
|
equipment
support & bases (link to this section
of the catalog)
pate® equipment support rails
provide leakproof mounting of rooftop units - with no worries about support
failure. Load bearing tested and rated, with certified data furnished on
request. Internally reinforced. Built to any length and designed to span roof
joists. Constructed of heavy-gauge galvanized steel, with continuous welded and
mitered corner seams. Integral base plate and galvanized steel counterflashing.
Pressure treated wood nailers. Styles and heights to match roof deck and
equipment requirements. For your protection, always require certified load bearing
data for any equipment supports on your project.
pate® combination equipment
bases are integral one-piece supports that prevent leaks around rooftop
hvac units. pate designs and builds them in sizes to fit heating and air
conditioning equipment and in two configurations to meet roof and job
requirements:
sceb = curb with attached solid top platform
mounting, and ceb = curb with attached mounting rails.
Field design, construction, and assembly costs are eliminated.
Unless project, size, or shipping requirements dictate otherwise, bases are shipped
completely assembled. Constructed of reinforced galvanized steel with all
welded metal components, factory installed insulation. Pressure treated wood
nailers. Heavy-gauge galvanized steel counterflashing. Available in three
styles (see page 2): sceb-1 = canted = ceb-1, sceb-2 = no cant = ceb-2, sceb-5 =
raised cant = ceb-5.
BACK TO TOP OF PAGE
|
|
|
|
|
|
|
|
|
|
|
|
expansion
joints (link to this section of the catalog)
pate® expansion
joints and wall cant curbing is a complete system for preventing leaks from roof
deck expansion and contraction. Includes expansion joint curb in desired lengths,
v-shaped spreader clips, corners, and termination end sections. Available in canted,
no cant, or raised cant styles (see page 2) and special heights and pitches.
Full mitered and welded corner sections combine to make tees or crosses.
Sloping end sections for termination points. Heavy-gauge galvanized steel
construction with integral base plate. Angle steel reinforcement, pressure treated
wood nailer, 1 ½" thick fiberglass insulation. Expansion joint cover available
as an option (consult factory).
BACK TO TOP OF PAGE
|
|
|
|
|
|
|
|
|
|
|
|
pipe
roller supports (link to this section of the catalog)
pate® pipe
roller supports are built to handle long runs of roof-mounted pipe - any size,
any type, any roof. Extra-heavy-duty components hold up under unusual stresses and
prevent roof leaks. Easy vertical and horizontal adjustment to accommodate gas,
electric, refrigerant and other service lines. Allows pipe to expand and contract
freely without affecting roof membrane. Roller assembly has locking device to
maintain pipe location. Adaptable to permit running any number of pipes parallel on
one base. Low in cost, easy to install, pate pipe roller supports
(prs) are available with pate equipment supports in styles to match roof
construction. For equipment support base detail, see page 2.
BACK TO TOP OF PAGE
|
|
|
|
|
|
|
|
|
|
|
|
skylights, hatches & smoke vents
(link to this section of the catalog)
acrylic skylights from pate®
help building designers utilize daylight in areas big and small and conserve energy in hot
or cold weather. Single or double dome designs are thermoformed from acrylic plastic
and available in clear colorless, translucent white, and solar bronze. Frames are
corrosion-resistant extruded aluminum, fully weatherproofed. Thermal models are
double dome. Skylights are supplied complete, ready for installation on 1 ½"
or wider prepared roof curbs. pate will provide the ideal match of
roof curbs to your skylights, avoiding misfits and delays on your project.
continuous vault skylights let the architect go to
almost any lengths in utilizing daylight. Single or double end barrel vaults are
thermoformed acrylic in 2' to 4' lengths to accommodate overall unit requirements.
Widths from 2' to 10' in any length greater than 8'. Vertical glazed ends are cold
formed acrylic. One-piece curb frame of extruded aluminum is designed for fastening
on 1 ½" or wider prepared roof curbs. Clearance for expansion and contraction
is provided in both the aluminum and acrylic areas.
smoke and heat vents mounted on roof open
automatically to release heat and fumes in the event of fire or explosion.
Fusible-link activated at 165° F or selectable higher ratings depending on normal ambient
temperature at ceiling level. Single or double-leaf acrylic domes or insulated
aluminum covers, all-aluminum curb and body assembly with integral cap flashing and
4" roof flange. Powerful spring-lift mechanism opens vent cover against wind
and snow loads. Inside manual release. Models available with UL listed and/or
FM Approved labels. Consult pate about options, other models.
BACK TO TOP OF PAGE
|
|
|
|
|
|
|
|
|
|
|
|
pipe curb
assemblies (link to this section of the
catalog)
pate® pipe curb assembly prevents
leaks when pipes go through a conventional or metal roof. All-in-one unit needs
only one roof opening, is leakproof and durable under all weather conditions. Comes
ready to install, including: roof curb, thermoplastic cover with sleeves scored for
as many as 4 pipes from ½" to 10" o.d., and watertight boots graduated for
standard pipe sizes, with adjustable stainless steel clamps. Multiple units
available with curb caps for virtually any number and variety of pipes. For curb
detail: click here [will link to catalog] (conventional roof) or
click here [will link to catalog] (metal
roof). Cover options:
pcc-1 for up to 4 pipes: ½"-2½" nominal
pcc-2 for up to 2 pipes: ½"-2½" nominal and 1 pipe
3"-5" nominal
pcc-3 for up to 2 pipes: ½"-2½" nominal and 2 pipes
3"-5" nominal
pcc-4 for 1 pipe: 6"-10" nominal
pcc-5 for 5 pipes: ½"-2½" nominal
BACK TO TOP OF PAGE
|
|
|
|
|
|
|
|
|
|
|
|
pipe
seals & dektites (link to this section of
the catalog)
pipe flashing devices for metal roofs seal
individual pipe penetrations in a matter of minutes. Flexible, one-piece flashing
conforms to panel profile and roof pitch of any metal building. Molded of
weather-resistant E.P.D.M. rubber. Aluminum ring base can be contoured to any area
of metal roof pane. Quickly installed with stainless steel fasteners.
Available in 9 sizes for pipes from ¼" to 18" in diameter. Isolates pipe
movement from vibration and expansion/contraction.
pate® pipe seal prevents
leaks from single-pipe openings in conventional roofs. Integral unit flashes and
weatherproofs rooftop penetrations - and at the cost of a pitch pocket.
One-piece spun aluminum base flashes easily into any roofing system. Full 5"
seal above base is sloped for runoff. Allows for pipe expansion and contraction or
vibration without leakage. Two sizes:
pps-3" for pipes from ½"-2½" nominal
(uninsulated)
pps-6" for pipes from 3"-5" nominal (uninsulated)
new pps-12" for pipes from
6"-10" nominal (uninsulated)
BACK TO TOP OF PAGE
|
|
|
|
|
|
|
|
|
|
